ACV 42xbm003 - LFB BMW 3 Series/5 Series/7 Series/X5/Mini 17 Pin Multilead IBus

Steering Wheel Remote Control Adapter BMW / Mini

Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings, and steering wheel remote control for proper functionality.

Note

• I Bus
• Connector: 17-pin BMW connector
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• If the BMW connector variant is unknown > Item: 42xbm00c with 17-pin and 40-pin Quadlock wiring harness
• Vehicles with Business OEM device
• Vehicles without Professional OEM navigation*
• Vehicles without OEM sound system**
• Remove OEM additional components:
• CD changer / TV tuner / telephone module
• Dipp switch settings for the aftermarket device manufacturer (see BDA)

Suitable for the following vehicles

• BMW 3 Series (E46) 07/1998 - 02/2007
• BMW 5 Series (E39) 01/1996 - 05/2004
• BMW 7 Series (E38) 09/1994 - 09/2001
• BMW X5 (E53) 03/2000 - 10/2003
• BMW Mini (R50/R53) 06/2001 - 11/2006
• BMW Mini (R52) 07/2004 - 08/2008

The following signals are provided

Reimported vehicles or vehicles with different software may be functionally incompatible.
Steering wheel remote control
*Vehicles with Professional Navigation BMW extension 17-pin (f) > 17-pin (m)/antenna 6.5m > Article: 1020-21-6500-0
**Vehicles with sound system (not DSP/Harman Kardon) active system adapter BMW/Land Rover/Rover 17-pin > Article: 13-1020-50 

General Installation Instructions

Verification:
1: Check all operating functions and vehicle adjustment functions of the OEM device
2: Disassemble the OEM device with the power off
3: Check all interface connections for correctness and continuity with the power off

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface with the power off
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the retrofit device's operating instructions.
4: Connect all other connections according to the retrofit device's operating instructions.
5: Connect the entire installation to the vehicle, making sure the power connection is the last.
6: Configure the interface's software according to the instructions in the article text and the user manual.
7: Configure the retrofit device according to the retrofit device's operating instructions: steering wheel remote control/camera/HFC/antenna phantom power, and more.
8: Test the steering wheel remote control and vehicle's functionality.
Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes with the power off.
2: Connect after changes, see steps 5 to 8 above.

If the interface or the vehicle malfunctions:
1: Revert to the OEM device.
2: Operate the OEM device.
3: Restoring the CAN bus to a standstill.
/>4: Checking the hardware configuration of the Interfaces
5: Connection to CAN bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for the guidance and information of trained specialist personnel.

Further connections, changes to the cable configuration of the wiring harness or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained specialist personnel.
2: Connections and modifications must be checked before connection for any manufacturer approvals or for any manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for functionality and accuracy before connection by measuring and comparing them with the vehicle's cable assignment plan.
4: Connections and modifications are made at your own risk and without a guarantee of functionality.
5: Connections and modifications are made at your own risk and without a guarantee of damage to the vehicle, the retrofit device, or the interface.
6: Modifications to the pre-assembled wiring harness may void the product's warranty.