ACV 42xrn004 - LFB Dacia/Opel/Renault vehicles ISO/Mini ISO Multilead loose

Steering Wheel Remote Control Adapter Dacia / Opel / Renault

• Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
• Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
• Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
• Please also check whether one of the specified original factory radios was installed in your vehicle.
• Check the vehicle functions, vehicle settings, and steering wheel remote control for functionality before final assembly.

Note

• analog
• Connector: ISO / Mini ISO yellow /  Mini ISO connector 6 pin occupied
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Dacia vehicles with Blaupunkt 1-DIN OEM device without external display
• Opel / Renault vehicles with Tuner List / Update List OEM device with display in the device
• Opel / Renault vehicles without Carminat Device
• Vehicles Opel / Renault without Cabasse sound system
  
• Dipp switch settings for the retrofit device manufacturer (see BDA)

For the following vehicles suitable

• Dacia Duster (SD) 04/2010 - 11/2013
• Dacia Sandero (SD) 06/2008 - 12/2012
• Opel Vivaro (X83) 09/2006 - 12/2010
• Renault Clio II 09/1998 - 09/2005*
• Renault Megane I (BA) 10/2000 - 09/2003
• Renault Megane II (CM/EM) 10/2002 - 12/2005
• Renault Kangoo (KC) 01/1998 - 09/2005
• Renault Twingo (C06) 01/2003 - 07/2007

The following signals are provided

Reimported vehicles or vehicles with different software may be functionally incompatible.
Steering wheel remote control
*OEM devices with external display

General installation instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Disassemble the OEM device without voltage
3: Verification Check all interface connections for correctness and continuity without voltage.

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface without voltage.
2: Check the configuration of the radio connection cable.
3: Connect the radio connection cable according to the operating instructions for the retrofit device.
4: Make all other connections according to the operating instructions for the retrofit device.
5: Connect the entire installation to the vehicle with the live connection last.
6: Configure the software of the interface according to the instructions in the article text and in the BDA.
7: Configure the retrofit device according to the operating instructions for the retrofit device, steering wheel remote control/camera/HFS/antenna phantom power and others.
8: Function test of the steering wheel remote control and vehicle.

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without voltage.
2: For connection after changes, see above 5 to 8

In case of malfunction of the interface or the vehicle:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest, see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only for trained specialist personnel.

Further connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and modifications are to be carried out exclusively by trained specialist personnel.
2: Connections and modifications are to be checked before connection for any manufacturer approvals or for any manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications are to be checked for function and Check for accuracy.
4: Connections and modifications are made at your own risk and without guarantee of functionality.
5: Connections and modifications are made at your own risk and without guarantee of damage to the vehicle, the retrofit device, or the interface.
6: Modifications to the pre-assembled wiring harness may void the product's warranty.