ACV 42xfo018 - LFB Ford various vehicles 24-pin multi-lead USB/AUX

Steering Wheel Remote Control Adapter Ford

• Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
• Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
• Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
• Please also check whether one of the specified original factory radios was installed in your vehicle.
• Check the vehicle functions, vehicle settings, and steering wheel remote control for proper functionality before final assembly.

Note

• CAN Bus
• Connector: 24-pin Ford connector
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Connector: OEM AUX > RCA red/white
• Connector: OEM USB > USB-A
• Vehicles with OK and/or voice function button
• Vehicles with OEM display
• Vehicles with SYNC function not supported
• Date/time settings not Supported
• Vehicle settings not supported
• Dip switch settings for the aftermarket device manufacturer (see BDA)

Suitable for the following vehicles

• Ford Everest 2015 - 2020
• Ford Ranger (2AB) 01/2016 - 01/2019
• Ford Ranger (2AB) 01/2019 - 2021
• Ford Transit Custom (FAC/FAD) 06/2016 - 01/2018*/**
• Ford Transit (V363) (FCA/FAD) 06/2016 - 06/2019*/**/***

The following signals are provided

Reimported vehicles or vehicles with different software may be functionally incompatible.

red: +12V ignition terminal 15
orange: +12V lighting terminal 58
purple/white: +12V reversing signal
pink: speed signal
green: ground GND Handbrake signal

Output load capacity: 250 mA max.

Current requirement greater than 250 mA:
1 relay coil resistance 75 Ohm min.
2 relay coil resistance 150 Ohm min.
 
Steering wheel remote control
 
*OEM USB/AUX connection not supported
**Vehicles with Euro 6 emissions standard
**Vehicles with Euro 5 emissions standard > 42xfo008
**Vehicles without OEM display > Article: 42xfo015
***OEM display installation of radio installation panel not supported:
OEM display must remain connected

General Installation Instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Disassemble the OEM device with the power off
3: Check all interface connections for correctness and continuity with the power off
Connection and connection sequence:
1: Make the settings and hardware configuration of the interface with the power off
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the Complete installation on the vehicle with a live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/HFCE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes with the power off
2: Connection after change, see above 5 to 8

In case of a malfunction of the interface or the vehicle:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest, see above 5 to 8

Connections specified in the information text or the operating instructions, Connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables are intended solely for guidance and information purposes for trained personnel.

Further connections, changes to the cable configuration of the wiring harness, or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained personnel.
2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for functionality and accuracy by measuring and comparing them with the vehicle's cable assignment plan.
4: Connections and modifications are made at your own risk and without a guarantee of functionality.
5: Connections and modifications are made at your own risk and without a guarantee of damage to the vehicle, the retrofit device, or the interface.
6: Modifications to the pre-assembled wiring harness may void the product's warranty.