ACV 42xns025 - LFB Nissan vehicles 20-pin/24-pin multi-lead camera

Steering Wheel Remote Control Adapter Nissan

Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings, and steering wheel remote control for proper functionality.

Note

• CAN Bus
• Connector: 20-pin / 32-pin Nissan connector
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Connector: OEM AUX > Cinch(m) red/white
• Connector: OEM USB > USB-A
• Connector: OEM 360° camera system > Cinch(m) yellow
• Vehicles with OEM navigation
• Vehicles with 360° camera system
• Vehicles with N-Connecta model equipment
• Vehicles with model equipment N-Vision
• Vehicles with Tekna model trim > Nissan Safety Shield not supported:
• Motion detection
• Parking assist
• Drowsiness detection
• Blind Spot Assist
• Date/Time Settings > FIS in AUX Position
• FIS reset to factory settings and reconfiguration required if AUX menu item is missing
• Track forward / Track back > Function may be reversed.
• OEM AUX:
• Check for correct assignment before installation by measuring with the OEM device.
• Dipp switch settings for the aftermarket device manufacturer (see BDA)

Suitable for the following vehicles

• Nissan Kicks 05/2017 - 08/2020
• Nissan Qashqai (J11) 03/2014 - 10/2018
• Nissan Rogue II 2014 - 2019
• Nissan X-Trail (T32) 07/2017 - 08/2018

The following signals are provided

• Reimported vehicles or vehicles with different software may be functionally incompatible.
• Red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V reversing signal
• pink: speed signal
• green: ground GND handbrake signal
• Output load capacity: 250 mA max.
• Current requirement greater than 250 mA:
• 1 relay coil resistance 75 ohms min.
• 2 relays coil resistance 150 ohms min.
• Steering wheel remote control
• Date/time settings supported
• 360° OEM camera system supported

General Installation Instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Disassemble the OEM device with the power off
3: Check all interface connections for correctness and continuity with the power off
Connection and connection sequence:
1: Make the settings and hardware configuration of the interface with the power off
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device.
4: Connect all other connections according to the operating instructions for the retrofit device.
5: Connect the entire installation to the vehicle, making sure the power is on last.
6: Software configuration of the interface according to the instructions in the article text and in the BDA.
7: Configuration of the retrofit device according to the operating instructions for the retrofit device, steering wheel remote control/camera/HFCE/antenna phantom power and others.
8: Function test of the steering wheel remote control and vehicle.
Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes with the power off.
2: Connect after changes, see 5 to 8 above.

In case of a malfunction of the interface or the vehicle:
1: Revert to the OEM device.
2: Operate the OEM device.
3: Establish CAN bus rest.
4: Check the hardware configuration of the Interfaces
5: Connection after CAN bus rest, see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only.

Further connections, changes to the cable configuration of the wiring harness or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained specialist personnel.
2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment plan.
4: Connections and modifications are made at your own risk and without a guarantee for function.
5: Connections and modifications are made at your own risk and without a guarantee for damage to the vehicle, the retrofit device or the interface.
6: Changes to the pre-assembled wiring harness may void the the product's warranty