ACV 42xrn008 - LFB Nissan/Opel/Renault 12Pin/32Pin Multilead

Steering Wheel Remote Control Adapter Nissan / Opel / Renault

Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings, and steering wheel remote control for proper functionality.

Note

• CAN Bus
• Connector: 12-pin / 32-pin Dacia / Nissan Connector
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Date/time setting supported
• Dip switch settings for the aftermarket device manufacturer (see BDA)

Suitable for the following vehicles

Nissan NV400 (M) 07/2014- 07/2020*
Nissan NV400 (M) 07/2020 - 12/2021*
Opel Movano B (X62) 06/2013 - 09/2019*
Renault Capture (R) 06/2013 - 12/2019*
Renault Clio IV (X98) 11/2012 - 06/2016**
Renault Clio IV (X98) 06/2016 - 12/2020**
Renault Grand Scenic 04/2012 - 09/2016****
Renault Master III (M) 09/2014 - 09/2019*
Renault Megane III (Z/BZ) 04/2012 - 12/2013
Renault Megane III (Z/BZ) 01/2014 - 07/2016***
Renault Scenic (JZ) 02/2012 - 09/2016****
Renault Trafic III (J/JL) 09/2014 - 07/2019****/*****
Renault Trafic III (J/JL) 09/2019 - 03/2022**/****/*****
Renault Twingo II (N) 01/2012 - 07/2014****
Renault Twingo III (AH) 09/2014 - 04/2019*****
Renault Wind (N) 08/2010 - 08/2013****

The following signals are available provided

• Reimported vehicles or vehicles with different software may be functionally incompatible.
• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V Reverse signal
• pink: speed signal
• green: ground GND Handbrake signal
• Output load capacity: 250 mA max.
• Power requirement greater than 250 mA:
• 1 Relay coil resistance 75 Ohm min.
• 2 Relay coil resistance 150 Ohm min.
• Steering wheel remote control
• *Vehicles without OEM Navigation
• *Vehicles with 1-DIN OEM radio, black, with front AUX/USB
• *Vehicles with 1-DIN OEM radio, black, with front AUX/USB 2 x chrome rotary knobs
  **Vehicles with R-Link OEM navigation monitor and Silverbox without front AUX/USB
  ***Vehicles with radio + Continental OEM device
  ****Vehicles with 1-DIN OEM device silver with front USB
  ****Vehicles with 1-DIN OEM device black with front USB > Article: 42xvx007
  *****Vehicles with R-Link OEM navigation
  
• **Vehicles with R-Link OEM navigation monitor and silver box without front AUX/USB
• ***Vehicles with radio + Continental OEM device
• ****Vehicles with 1-DIN OEM device silver with front USB
• ****Vehicles with 1-DIN OEM device black with front USB > Article: 42xvx007
• *****Vehicles with R-Link OEM Navigation

General Installation Instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Disassemble the OEM device with the power off
3: Check all interface connections for correctness and continuity with the power off
Connection and connection sequence:
1: Adjust the settings and hardware configuration of the interface with the power off
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with the live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/HFCE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes with the power off
2: Connect after change, see above 5 to 8

In case of a malfunction of the interface or the vehicle:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connect after CAN bus rest, see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the information text or the operating instructions are intended solely as a guide and for the information of trained personnel.

Further connections, changes to the cable configuration of the wiring harness, or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained personnel.
2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for function and accuracy by measuring and comparing them with the vehicle's cable assignment plan.
4: Connections and modifications are made at your own risk and without a guarantee of function.
5: Connections and modifications are made at your own risk and without a guarantee of damage to the vehicle, the retrofit device, or the interface.
6: Modifications to the pre-assembled wiring harness may void the product's warranty.