ACV 42xrn007 - LFB Nissan/Opel/Renault vehicles Multilead ISO loose

Steering Wheel Remote Control Adapter Nissan / Opel / Renault

Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings, and steering wheel remote control for functionality.

Note

• CAN Bus
• Connector: ISO / Mini ISO
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Vehicles with external display
• Vehicles without Arkamys DSP OEM sound system
• Vehicles without OEM device with own display without front USB
• Vehicles without Radiosat Classic OEM device > Please contact support.
• External OEM display must remain connected.
• Date/time setting supported.
• Dip switch settings for the aftermarket device manufacturer (see BDA)

Suitable for the following vehicles:

• Nissan NV 400 09/2010 - 06/2014
• Nissan Primastar (X83) 01/2011 - 05/2015*
• Opel Movano (B) 02/2010 - 08/2014
• Opel Vivaro B (X83) 01/2011 - 08/2014*
• Renault Clio III (R) 05/2009 - 04/2014
• Renault Grand Modus (P) 01/2008 - 03/2013
• Renault Grand Scenic 04/2009 - 09/2016
• Renault Laguna III (BT) 10/2007 - 09/2014
• Renault Master (III) 02/2010 - 08/2014
• Renault Modus (P) 04/2008 - 12/2012
• Renault Mégane (III) 2008 - 12/2013
• Renault Scenic III (JZ) 06/2009 - 02/2012
• Renault Trafic II (JL/FL/EL Facelift) 01/2011 - 08/2014*
• Renault Twingo II (N) 09/2009 - 12/2011*/**
• Renault Wind (N) 08/2010 - 08/2013**

The following signals are provided

• Reimported vehicles or vehicles with different software may be incompatible in terms of functions be.
• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V Reverse signal
• pink: speed signal
• green: ground GND handbrake signal
• Output load capacity: 250 mA max.
• Current requirement greater than 250 mA:
• 1 relay coil resistance 75 ohms min.
• 2 relay coil resistance 150 ohms min.
• Steering wheel remote control
• *Vehicles with OEM device with own display without front USB > Item LFB Nissan/Renault ISO/Mini ISO yellow/OEM device with display: 42k-1250-000
• **Vehicles with Update List OEM device without display

General Installation Instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device.
2: Disassemble the OEM device with the power off.
3: Check all interface connections for correctness and continuity with the power off.

Connection and connection sequence:
1: Settings and hardware configuration of the interface without voltage.
2: Check the configuration of the radio connection cable.
3: Connect the radio connection cable according to the operating instructions for the retrofit device.
4: Connect all other connections according to the operating instructions for the retrofit device.
5: Connect the entire installation to the vehicle, making sure the power is on last.
6: Configure the software of the interface according to the instructions in the article text and in the user manual.
7: Configure the retrofit device according to the operating instructions for the retrofit device, steering wheel remote control/camera/HFS/antenna phantom power, and more.
8: Test the functionality of the steering wheel remote control and the vehicle.
Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without voltage.
2: For connection after changes, see 5 to 8 above.

If the interface or the vehicle malfunctions:
1: Revert to the OEM device.
/>2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest, see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance only and for the information of trained specialist personnel.

Further connections, changes to the cable configuration of the wiring harness or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained specialist personnel.
2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment plan.
4: Connections and modifications are made at your own risk and without any guarantee of function.
5: Connections and modifications are made at your own risk and without any guarantee of Damage to the vehicle, the aftermarket device, or the interface
6: Modifications to the pre-assembled wiring harness may void the product's warranty