ACV 42xty014 - LFB Toyota vehicles 28Pin/34Pin/10Pin Multilead

Toyota Steering Wheel Remote Control Adapter

Retain the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle's equipment, as well as the range of functions and software of the aftermarket device, individual control functions may be omitted or replaced by other functions.
Compare the adapter connectors shown with those in your vehicle and ensure that they are visually and technically compatible.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings, and steering wheel remote control for proper functionality.

Note

• analog
• Connector:  28 pin /  34 pin / 10 pin Toyota connector
• Connector: OEM steering wheel remote control > 3.5mm jack / loose cable
• Connector: OEM AUX > 3.5 mm jack (m)
• Connection: OEM rear view camera > RCA (m) yellow camera input
• Purple/white: +12V reversing signal
• Vehicles with different pin assignments:
• To avoid malfunctions or defects on the vehicle or the retrofit device, check the pin assignment by measuring before connection.
• Camera +6V power supply > Check for correct assignment with OEM device before installation
• Video (+/-) > Check for correct assignment with OEM device before installation
• USB > Check for correct assignment with OEM device before installation
• AUX > Check for correct assignment with the OEM device before installation.
• Dipp switch settings for the retrofit device manufacturer (see BDA)

Suitable for the following vehicles:

• Toyota Aygo X (AB7) 04/2022 - 2025
• Toyota Camry (XV70) 03/2019 - 04/2021
• Toyota Camry (XV70) 04/2021 - 09/2021
• Toyota Hilux (AN1P) 10/2020 - 2025
• Toyota Yaris (XP21) 09/2020 - 2025

The following signals are available frame

• Reimported vehicles or vehicles with different software may be functionally incompatible.
• Steering wheel remote control
• OEM rear view camera

General installation instructions

Verification:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Disassemble the OEM device without voltage
3: Check all interface connections for correctness and continuity without voltage

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface without voltage
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with a live connection last
6: Configure the software of the interface according to the instructions in the article text and in the BDA
7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/HFS/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the Radio connection cable:
1: Make changes with the power off.
2: For connection after change, see above 5 to 8.

If the interface or vehicle malfunctions:
1: Revert to the OEM device.
2: Operate the OEM device.
3: Establish CAN bus rest.
4: Check the interface's hardware configuration.
5: For connection after CAN bus rest, see above 5 to 8.

Connections, connection changes, alternative connections, connections of loose cables, or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only.

Further connections, changes to the cable configuration of the wiring harness, or the use of alternative connections or connection extensions:
1: Connections and modifications may only be carried out by trained specialist personnel.
2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes.
3: Connections and modifications must be checked for functionality and accuracy before connection by measuring and comparing them with the vehicle's wiring diagram.
4: Connections and modifications are made at your own risk and without any guarantee of functionality.
5: Connections and modifications are made at your own risk and without any guarantee of damage to the vehicle, the retrofit device, or the interface.
6: Modifications to the pre-assembled wiring harness may void the product's warranty.