ACV 42xvw015-0 - LFB for Seat/Skoda/VW

Steering wheel remote control adapter Seat / Skoda / VW

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle equipment and the range of functions and software of the  retrofit device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

For the following vehicles suitable:

Seat

• Seat Alhambra II (7N) 06/2016 - 08/2019
• Seat Mii (AA) 05/2017 - 06/2019
• Seat Mii (AA) 01/2020 - 02/2021

Skoda

• Skoda Citigo (AA) 05/2017 - 06/2019*
• Skoda Citigo iv (AA) 01/2020 - 08/2021*

VW

• VW Amarok (2H) 09/2016 - 07/2020**
• VW Beetle (16) 06/2016 - 03/2018
• VW Caddy IV (DU) 06/2015 - 09/2020
• VW Crafter II (SY/SZ) 03/2017 - 2024
• VW Grand California (SY/SZ) 03/2019 - 2024
• VW Sharan II (7N) 07/2015 - 10/2021
• VW Tiguan II (5N) 05/20 16 - 05/2021
• VW T6 (7HC) 07/2015 - 08/2019***
• VW UP! (AA) 07/2016 - 12/2020****

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V reversing signal
• pink: speed signal
• green: ground GND Handbrake signal

Output load capacity: 250 mA max.
Current requirement greater than 250 mA:

• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min
• Steering wheel remote control

*Vehicles with LG Anatel L169SK2 OEM device
**Vehicles with OEM device including CD drive
***Vehicles without Composition Audio MIB Entry OEM device with front AUX/SD/USB
***Vehicles with Composition Audio MIB Entry OEM device with front AUX/SD/USB > Article: 42a-1324-001
****Vehicles without OEM sound system                      

General installation instructions:

Check:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power supply
3: Check all interface connections for correctness and continuity without power supply

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation on the vehicle with a live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without voltage
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the Interfaces
5: Anschluss to CAN bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Other connections, changes to the cable configuration of the cable harness or use of alternative connections or connection extensions:
1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked before connection for any manufacturer approvals or for any manufacturer warranty conditions that may be affected by the changes
3: Connections and changes must be checked before connection by measuring and by comparing them using the Cable assignment plan of the vehicle to check for functionality and correctness
4: Connections and changes are made at your own risk without guarantee of functionality
5: Connections and changes are made at your own risk without guarantee of damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness can void the product's warranty lead